INS Optical TAP Interface Panels

An Optical TAP provides access to the full-duplex data stream while maintaining uninterruptible data flow within the network for performance engineers to utilize monitoring systems or protocol analyzers. Optical TAPs will induce attenuation on the network link so be sure to verify optical power budget prior to implementing to avoid unnecessary troubleshooting. Optical TAPs do not create latency or delay.

FEATURES

  • No power or adjustments are required
  • All traffic (raw data) is funneled to monitor port for analyzing
  • Allows connecting and disconnecting to monitoring traffic without taking the network off line
  • Custom split ratio, chassis and modules available

MPO/MTP PRE-TERMINATED SYSTEMS

The INS MPO/MTP Module is a pre-terminated, pre-tested, rack mount module system allowing for a simple installation of MPO/MTP backbone cables with a transition to standard LC or SC connections. The INS modules are designed to fit into enclosures with LGX slot configurations. Using a pre-terminated cable assembly in conjunction with modules within a rack allows for easier installation and simpler cable management. Contact your INS sales representative today for further details or use the part numbers and configurator below to construct the proper combination to meet any requirement.

MPO/MTP STOCK BREAKOUT MODULE SOLUTION

PART #
DESCRIPTION

P45-F1-MTP-M-SC-OM3-12

12-fiber 50μm OM3, 1 rear MTP/male port, 6 SC/duplex ports

P45-F1-MTP-M-SC-OS2-12

12-fber SM, 1 rear MTP/male port, 6 SC/duplex ports

P45-F1-MTP-M-LC-OM3-12

12-fiber 50μm OM3, 1 rear MTP/male port, 6 front LC/duplex ports

P45-F1-MTP-M-LC-OS2-12

12-fiber SM, 1 rear MTP/male port, 6 front LC/duplex ports

P45-F1-MTP-M-LC-OM3-24

24-fiber 50μm OM3, 2 rear MTP/male ports, 6 front LC/quad ports

P45-F1-MTP-M-LC-OS2-24

24-fiber SM, 2 rear MTP/male ports, 6 front LC/quad ports

** Also available with MTP / Female Ports and/or SC ports **

Assemblies Couplers/ Splitters

INS couplers and WDM’s are designed, manufactured, and tested to meet a variety of high performance and environmental requirements. Our high quality couplers are available in single wavelength and dual window varieties in an assortment of split ratios. Our WDM’s feature low insertion loss in combination with high isolation. All device types are available in bare fiber, 900μm, or 3mm ruggedized versions and can be terminated with your choice of connectors or installed in a variety of modules.

SINGLEMODE DUAL WINDOW COUPLERS/SPLITTERS

250μm

Buffered Fiber

PART #
DESCRIPTION

P40-SDW13550122UC

1x2 (1310/1550nm) 50/50 Ratio

P40-SDW13510122UC

1x2 (1310/1550nm) 10/90 Ratio

P40-SDW13520122UCTS

1x2 (1310/1550nm) 20/80 Ratio

P40-SDW13530122UCTS

1x2 (1310/1550nm) 30/70 Ratio

P40-SDW13540122UCTS

1x2 (1310/1550nm) 40/60 Ratio

P40-SDW13550222UC

2x2 (1310/1550nm) 50/50 Ratio

900μm

Buffered Fiber

PART #
DESCRIPTION

P40-SDW13550129UCTS

1x2 (1310/1550nm) 50/50 Ratio

P40-SDW13550129UCTS

1x2 (1310/1550nm) 10/90 Ratio

P40-SDW13520129UCTS

1x2 (1310/1550nm) 20/80 Ratio

P40-SDW13530129UCTS

1x2 (1310/1550nm) 30/70 Ratio

P40-SDW13540129UCTS

1x2 (1310/1550nm) 40/60 Ratio

P40-SDW13550229UCTS

2x2 (1310/1550nm) 50/50 Ratio

P40-SDW1351X3333333129CTS

1x3 (1310/1550nm) 33/33/33 Ratio

MULTIMODE COUPLERS/SPLITTERS (800-1600nm)

250μm

Part #
Description

P40-MMC28550122CTS

1x2 62.5/125μm Coupler 50/50 Ratio 250μm Fiber

    P40-MMC38550122CTS

    1x2 50/125μm Coupler 50/50 Ratio 250μm Fiber

    900μm

    PART #
    DESCRIPTION

    P40-MMC28550129CTS

    1x2 62.5/125μm Coupler 50/50 Ratio 900μm Fiber

    P40-MMC28550229C

    2x2 62.5/125μm Coupler 50/50 Ratio 900μm Fiber

    P40-MMC38550129CTS

    1x2 50/125μm Coupler 50/50 Ratio 900μm Fiber

    WAVELENGTH DIVISION MULTIPLEXERS

    A Wave Division Multiplexer (WDM) is a coupler that enables you to channel a signal to multiple devices operating at different wavelengths.

    250μm

    PART #
    DESCRIPTION

    P40-WDM13550122UCTS

    1x2 Sm Dual Window (1310/1550nm) WDM 250μm Fiber

    900μm

    PART #
    DESCRIPTION

    P40-WDM13500129UC

    1x2 Sm Dual Window (1310/1550nm) WDM 900μm Fiber

    P40-WDM13500229UC

    2x2 Sm Dual Window (1310/1550nm) WDM 900μm Fiber

    SPLITTER TAP LGX STYLE MODULES

    These LGX modules are loaded with completely passive optical splitter packages and are configured to meet specific Test Access Point (TAP) requirements. They provide monitor access to live network links without disrupting service on the network. Custom configurations, split ratios and connector styles are available.

    PART #
    DESCRIPTION

    P45-RMC-3-S-2-50-YU-YU-6

    LGX Style Module, 1x2, 50/50 split, SC/UPC

    P45-RMC-3-S-2-50-YA-YA-6

    LGX Style Module, 1x2, 50/50 split, SC/APC

    P45-RMC-3-S-2-35-YU-YU-6

    LGX Style Module, 1x2, 65/35 split, SC/UPC

    P45-RMC-3-S-2-20-YA-YA-6

    LGX Style Module, 1x2, 80/20 split, SC/APC

    P45-RMC-3-S-2-10-YA-YA-6

    LGX Style Module, 1x2, 90/10 split, SC/APC